How to make a paper hand
From paper you can make a lot of all different, including hand. By the way, recently it is quite often possible to hear about how to make a paper hand. And it is not surprising, after all, it's one thing to fold out of the paper for a long time to all familiar flap, but another to make your hand, and also very similar to human. It should be noted that there is nothing complicated.
First you need to decide how the hand will be made. There are quite a lot of ways, but only among them there are only a few, as a result of which the realization of which is really a good deal.
For affairs you will need a square of paper, for example, A4 printer paper.
First, the square must be bent diagonally, the result is a triangle. Then the same needs to be done with another diagonal.
Next, the workpiece must be bent along and across, each time unfolding after the previous fold.
Next, it is necessary to make a double triangle, after which the angles of the resulting triangle must be bandaged on the right side. At the next stage, you need to repeat the bend of the corners, and then go back to step back. By the way, if you flexing the angles are not right, but on the left side, then the result will be left hand.
Then from the triangle it is necessary to make the harmonica, of course, smooth.
When the harmonica is ready to bend the upper angle, it is necessary to bend it to the opposite edge, and it is necessary after straightening. It is done in order to get a fold, which comes across the triangle in the middle.
It is necessary to bring the resulting seal to the resulting seal, after which, the same to do from the opposite side, and follow its edge to the top and turn the blank.
Next, the task is to enjoy the edge of the triangle, the top of which should be settled in the middle of the figure. As a result, the triangular harmonica should be obtained. After, the same must be done in the case of the opposite face.
The resulting triangular harmonica must be deployed so that it turns out the triangle.
Next, the lower angle should be wrapped up, as a guide in this case, you can use a fold line, which is located vertically in the upper edge.
Well, and then you need to take up the creation of the harmonica again. Sliding the ends can be used to ultimately how to get five fingers, if more precisely, billets, of which later and you need to form your fingers. Fingers need to give volume, and then make them as much as possible. https://xgeneve.ch
First you need to decide how the hand will be made. There are quite a lot of ways, but only among them there are only a few, as a result of which the realization of which is really a good deal.
For affairs you will need a square of paper, for example, A4 printer paper.
First, the square must be bent diagonally, the result is a triangle. Then the same needs to be done with another diagonal.
Next, the workpiece must be bent along and across, each time unfolding after the previous fold.
Next, it is necessary to make a double triangle, after which the angles of the resulting triangle must be bandaged on the right side. At the next stage, you need to repeat the bend of the corners, and then go back to step back. By the way, if you flexing the angles are not right, but on the left side, then the result will be left hand.
Then from the triangle it is necessary to make the harmonica, of course, smooth.
When the harmonica is ready to bend the upper angle, it is necessary to bend it to the opposite edge, and it is necessary after straightening. It is done in order to get a fold, which comes across the triangle in the middle.
It is necessary to bring the resulting seal to the resulting seal, after which, the same to do from the opposite side, and follow its edge to the top and turn the blank.
Next, the task is to enjoy the edge of the triangle, the top of which should be settled in the middle of the figure. As a result, the triangular harmonica should be obtained. After, the same must be done in the case of the opposite face.
The resulting triangular harmonica must be deployed so that it turns out the triangle.
Next, the lower angle should be wrapped up, as a guide in this case, you can use a fold line, which is located vertically in the upper edge.
Well, and then you need to take up the creation of the harmonica again. Sliding the ends can be used to ultimately how to get five fingers, if more precisely, billets, of which later and you need to form your fingers. Fingers need to give volume, and then make them as much as possible. https://xgeneve.ch
